How to Read Wheel Size, Bolt Pattern and Offset (17x9, 6x5.5)
Share
Wheel specs read like a code: 17x8.5, 6x5.5, +18mm, 130.81mm CB, M14x1.5. Each number answers one question: will the wheel bolt on, clear your brakes and sit where you want it? Here is how to read them, using sizes from wheels in the catalogue.
Diameter and width: 17x9, 20x9
The first pair is diameter x width, in inches. A 20x9 wheel is 20 inches across at the bead seat, where the tire sits, and 9 inches wide between the bead seats. The tire must match the diameter exactly: a tire size ending in R20 goes on a 20-inch wheel. The width must fall in the tire's approved rim-width range.
A bigger diameter means a lower-profile tire for the same overall height: sharper steering, but less sidewall to soak up potholes. A smaller diameter leaves more sidewall, which suits winter and off-road use, as long as the wheel clears your brake calipers. Heavy-duty trucks with large brakes often cannot go down in size.
Bolt pattern: 6x5.5 is 6x139.7
The bolt pattern (also called PCD) is the number of lugs x the diameter of the circle through the centre of the studs. 6x5.5 means six lugs on a 5.5-inch circle. In metric the same pattern is 6x139.7, because 5.5 x 25.4 = 139.7 mm. Makers use both, so the RTX Wheels 20x9 6x139.7 +0mm Wheel and the Method Race Wheels 17X8.5 Nv 6X5.5 share one pattern even though it is written differently.
Common truck patterns:
- 5x5 (5x127): Jeep Wrangler JK and JL, Jeep Gladiator.
- 6x5.5 (6x139.7): GM half-tons, Ram 1500 from 2019, Toyota Tacoma and 4Runner.
- 6x135: Ford F-150 from 2004.
- 6x120: Chevrolet Colorado and GMC Canyon from 2015.
- 8x6.5 (8x165.1): Ram 2500/3500 and older GM heavy-duty trucks.
- 8x180: GM 2500/3500 from 2011.
Close patterns do not interchange: 6x135 and 6x139.7 differ by less than 5 mm, enough to stop the wheel seating on the studs. Confirm yours in the owner's manual; each product page lists the years, makes and models it fits.
Offset and backspacing
Offset is the distance in millimetres from the wheel's centreline to its mounting face. Positive offset, like the +18mm on the Method Race Wheels Mr701 Hd 18X9 +18Mm Offset 8X180, tucks the wheel in. Zero offset centres it. Negative offset pushes it out toward the fender.
Backspacing says the same thing in inches, measured from the mounting face to the inner lip. The Method 17x8.5 above lists 4.75 inches at 0 offset. To convert, take half the wheel width, add half an inch for the lip, then add the offset in inches. An 18x9 at +18mm comes to about 5.7 inches.
Pushing a wheel out widens the track, adds leverage on wheel bearings and ball joints, can rub the fender liner at full lock, and throws more salt and slush up the truck's sides. With a leveling kit or lift kit, follow the kit maker's offset and tire-size advice.
Centre bore and hub-centric rings
The centre bore (CB) is the hole in the middle of the wheel; the Method Mr701 lists 130.81mm. It must equal your hub or be larger. A matching bore lets the hub centre the wheel (hub-centric). Many aftermarket wheels use a larger bore to suit several trucks, and the lug nuts do the centring (lug-centric). That works with nuts torqued evenly in a star pattern, but a hub-centric ring, a plastic or aluminum sleeve sized to the wheel bore outside and the hub inside, makes mounting easier and helps prevent vibration.
Lug thread and seat type
Lug nuts must match both the stud thread and the wheel's seat. Thread is written diameter x pitch. M14x1.5 is listed on several products in Lug Nuts & Wheel Hardware and is used on GM and newer Ram trucks, the Toyota Tundra and the Jeep Wrangler JL. The Tacoma and 4Runner use M12x1.5, and the Ford F-150 uses M14x2.0, which looks nearly identical to M14x1.5 but will cross-thread.
Seat type is the shape where nut meets wheel: conical (the usual aftermarket seat), ball or radius, or flat with a washer. Match the nut to the wheel, not the truck. Wheels with small lug holes need spline-drive nuts turned with a key, and hex size (13/16 in on the Gorilla factory-style nuts) has to fit both your wrench and the lug hole.
Spacers vs adapters
A wheel spacer sits between hub and wheel and pushes the wheel out without changing the bolt pattern, much like lowering the offset. An adapter also changes the pattern, for example to put a 5x4.5 wheel on a 5x5.5 hub. Both are in Wheel Spacers & Adapters. Choose hub-centric designs, torque to the maker's spec and re-check after the first drive. Suspension lift spacers are a different part; read the product page before you order.
Winter wheels and TPMS
A second set of wheels for winter tires saves a mount-and-balance every spring and fall and keeps salt off your summer wheels. Many owners drop to a 17 or 18 instead of a 20 for more sidewall and a less costly tire, as long as it clears the brakes. Rinse salt off through the season, especially on milled or machined finishes. Some provinces require winter tires for part of the year; check your province's rules.
With direct TPMS, each wheel carries a pressure sensor, and without sensors in the winter set the warning light stays on all season. Buy sensors that work with your truck and have them programmed or relearned; the procedure varies by make. At each swap, clean rust off the hub face so the wheel sits flat, torque in a star pattern, and re-check torque after the first 50 to 100 km.
Browse Wheels or use the vehicle selector to narrow the list to your truck. Wheels ship across Canada and are priced in Canadian dollars.
FAQ
Is 6x5.5 the same bolt pattern as 6x139.7?
Yes. 6x5.5 is written in inches and 6x139.7 in millimetres; 5.5 inches is 139.7 mm. Either label fits a hub with that pattern if the centre bore, offset and brake clearance also work.
Can I reuse my factory lug nuts on aftermarket wheels?
Often not. The nut must match the stud thread and the wheel's seat, and factory nuts made for flat-seat or ball-seat wheels will not hold a conical-seat wheel properly. Buy nuts to the seat type the wheel maker specifies.
Do I need hub-centric rings?
If the wheel's centre bore is larger than your hub, a ring sized to both makes the wheel easier to centre when mounting and helps prevent vibration. If the bore matches your hub exactly, no ring is needed.
Do my winter wheels need TPMS sensors?
If your truck has direct TPMS and you want the warning light off, yes. Each winter wheel needs a sensor that works with your truck, and the sensors must be programmed or relearned to the vehicle.








